DIY Guide to Mounting Bindings on Maven Skis for Optimal Shredding

Getting Your Maven Skis Ready to Rip

It's finally time to strap on those new Maven skis and shred some powder! But before hitting the slopes, you'll want to make sure your skis are properly mounted with bindings so you can ride in control and comfort all season long. Mounting your own skis can be a fun DIY project if you have the proper knowledge and tools. In this guide, we'll walk through the step-by-step process of mounting bindings on Maven skis so you'll be ready to carve first tracks in no time!

Tools & Supplies Needed

Mounting bindings on your new Maven skis will require a few special tools and supplies:

• Bindings - Make sure to get bindings designed for your ski type, skill level, and weight
• Mounting jig - Holds skis securely while drilling holes for bindings
• Drill & drill bits - A power drill with the appropriate sized bit for pilot holes
• Screws - The specific screws provided with your bindings
• Screwdriver - For securing the binding screws in place
• Epoxy - Used to permanently affix the bindings
• Clamps - Help hold bindings in correct spot while epoxy sets
• Ruler & marker - For accurately measuring and marking your mount points
• Wax paper - Prevents epoxy drips on your new skis!

Step-by-Step Mounting Process

Once you've gathered all the tools and materials, you're ready to start mounting. Follow these steps:

1. Insert skis securely into mounting jig according to instructions
2. Determine exact middle of skis and mark clearly with marker
3. Place bindings evenly spaced at proper fore/aft positions on skis
4. Double check alignment against manufacturers specs
5. Pre-drill pilot holes using power drill and correct bit
6. Insert screws into pilot holes but do not fully tighten
7. Mix epoxy according to instructions and apply liberally beneath bindings
8. Use clamps to firmly press bindings into epoxy, squeezing out excess
9. Wipe away any excess epoxy with wax paper before drying
10. Once epoxy has fully cured, tighten all screws firmly with screwdriver
11. Allow several hours for epoxy to fully harden before using
12. Remove from jig and admire your handiwork!

Tips for Proper Mounting

Here are some helpful tips to ensure your Maven bindings are mounted securely and accurately:

• Consult manufacturer instructions for proper binding position - too far back risks tail heavy skiing!
• Always use drill stop with power drill to avoid penetrating topsheet
• Clean skis thoroughly before mounting to remove any oil or debris
• Use a mallet to lightly tap bindings into proper alignment
• Slowly tighten screws in criss-cross pattern for even pressure
• Ensure no epoxy gets into screw holes which can prevent binding release
• Let epoxy fully cure before skiing - don't be tempted by early laps!

Hitting the Slopes!

Once your Maven bindings are securely mounted, it's time to click in and take those new skis for a spin! Always remember to adjust your bindings for proper release settings based on your weight, height and skiing ability. Take a few runs to get a feel for your new setup and make any tweaks needed for optimal performance. With perfectly mounted bindings, you'll be ready to charge down the mountain all season long!

Mounting your own skis can be a very rewarding do-it-yourself adventure. But if you don't have the proper tools or patience for the process, don't hesitate to drop them off with your local ski shop's mounting experts. Their specialized equipment and experience will have you shredding in no time. However you get it done, proper binding mounting is a critical part of optimizing performance and safety. Now get out there and send it on those new Mavens!

FAQs

What binding mount system do Maven skis use?

Maven skis utilize the industry standard 4-hole mounting pattern. They are compatible with all major binding brands like Look/Rossignol, Salomon, Tyrolia, Marker, etc.

What angle should I set my bindings at?

Most skiers do well with their bindings set at 0-2 degrees of duck stance for optimal balance and control. Consult your local ski shop for help setting the exact angle based on your height and style.

Should I wax my skis before mounting bindings?

Yes, you should always wax and tune new skis prior to mounting bindings. This fills in pores and provides a smooth surface for binding epoxy adhesion.

What temperature range is best for epoxy curing?

Epoxy will fully cure fastest between 60-75°F. Colder temperatures can significantly increase cure time. Try to mount indoors if possible.

Can I adjust my binding position after mounting?

Unfortunately no, the epoxy mount is permanent. That's why careful measurement and alignment is so important during initial mounting.