FRS TRD Spoiler - Customize Your Scion FRS with Sporty Rear Spoiler Upgrade

What is an FRS TRD Spoiler?

The FRS TRD spoiler is an aerodynamic accessory designed specifically for the Scion FRS sports coupe. TRD stands for Toyota Racing Development, which is the high-performance division of Toyota. The FRS (also known as the GT86 in other markets) is a compact 2+2 sports car jointly developed by Toyota and Subaru.

The FRS TRD spoiler is intended to enhance the styling and aerodynamic performance of the FRS. It replaces the standard factory rear spoiler and is made from lightweight ABS plastic. The spoiler is finished in gloss black to match other TRD accessories and provides several benefits:

• Improved aerodynamics - The spoiler shape improves airflow over the rear of the car, increasing downforce on the rear axle for better high-speed stability.
• Aggressive styling - The TRD spoiler gives the FRS a more aggressive, performance-oriented look from the rear.
• Weight savings - The ABS plastic construction reduces weight compared to the stock spoiler.
• Customization - The TRD spoiler allows owners to customize the look of their FRS.

FRS TRD Spoiler Design

The FRS TRD spoiler has a distinctive dual-level design for maximum visual impact:

• The upper level of the spoiler extends upward and backward from the edge of the FRS's trunk lid. This surface provides the main downforce benefit.
• The lower level of the spoiler protrudes outward, flanking the FRS's center-mounted brake light. This helps smooth airflow off the sides of the vehicle.

This two-tier design gives the FRS TRD spoiler a technical, motorsports-inspired look. The upward sweep and raised outer edges also make the rear of the car appear lower and wider for an aggressive stance.

Dimensions

The FRS TRD spoiler has the following dimensions:

• Overall width: 67.3 inches
• Height at tallest point: 5.5 inches
• Overall length: 5.5 inches

Despite its assertive presence, the spoiler is carefully sized to integrate cleanly with the existing lines of the FRS rear. No drilling or modifications are required for installation.

Finish

To complement other TRD parts, the FRS TRD spoiler comes finished in gloss black as standard. For further customization, some aftermarket manufacturers also offer the spoiler in additional colors like carbon fiber, gloss red, or unpainted primer grey.

Construction

The FRS TRD spoiler is constructed from high quality ABS plastic. This provides several advantages compared to fiberglass or carbon fiber:

• Lightweight - Weighs less than factory spoiler
• Durable - Impact resistant even in cold weather
• Affordable - Lower cost than carbon fiber
• Easy installation - Pre-drilled holes for no-fuss attachment

Wind Tunnel Testing

During development, the FRS TRD spoiler went through extensive wind tunnel and computational fluid dynamics (CFD) testing. Engineers fine-tuned the shape and angles to produce optimal rear downforce and stability.

Testing validated the aerodynamic improvements over the stock spoiler. The double-decker design works in conjunction with the FRS's rear diffuser and other underbody elements to improve airflow and high-speed handling.

Weight Savings

Weighing in at just 4.2 pounds, the FRS TRD spoiler shaves precious grams off the rear of the car compared to the factory plastic spoiler. Since the rear end greatly impacts handling agility, reducing mass helps the FRS turn in and change direction faster.

Installing the FRS TRD Spoiler

While recommended for professional installation, it is possible for homeowners to install the FRS TRD spoiler themselves in their own garage with common tools and mechanical ability. Here are the steps involved:

1. Remove the stock spoiler - Take out the screws or bolts holding the OEM spoiler and unplug any electrical connectors.
2. Prep the trunk - Use alcohol to thoroughly clean the attachment area on the trunk lid.
3. Test fit the spoiler - Temporarily fit the TRD spoiler to check alignment and marking locations.
4. Mark holes - Use a felt pen to mark the pre-drilled hole locations from the new spoiler.
5. Drill holes - Use a drill and appropriate bit to open holes at the marked spots.
6. Attach the spoiler - Line up the spoiler and bolt it into place with the provided hardware.
7. Inspect alignment - Verify even gaps and that the spoiler sits flush with the trunk edges.
8. Tighten hardware - Tighten down the mounting bolts to the recommended torque specs.

With care, the spoiler can be installed smoothly in just a few hours. Having an extra set of hands helps with test fitting and holding the spoiler in place while drilling and tightening.

Where to Buy the FRS TRD Spoiler

There are a few options for purchasing an authentic FRS TRD spoiler:

• Toyota dealership - Genuine Toyota TRD parts can be ordered through your local Toyota dealer's parts department.
• Online TRD retailer - Sites like TRDShop.com sell official TRD accessories and ship nationwide.
• Auto parts stores - Some national chains like AutoZone offer the TRD spoiler for the FRS in-store or online.
• eBay - New and used FRS TRD spoilers can often be found auctioning on eBay Motors.

For the best fit and quality, opt for a factory direct Toyota or Scion-branded TRD spoiler. Aftermarket versions may not mount as precisely. Prices range from around $375-$475 for an OEM spoiler.

Key Benefits of the FRS TRD Spoiler

Here's a quick recap of the key advantages of adding the TRD spoiler to your Scion FRS sports car:

• Improved high-speed aerodynamics and stability.
• More aggressive appearance from the rear.
• Lightweight durable ABS plastic construction.
• Easy no-drill installation.
• Finished in dark gloss black.
• Wind tunnel tested for maximum performance.

Along with other TRD upgrades like lowering springs, exhaust, and body kits, the rear spoiler is a great way to enhance both the look and performance of the FRS.

FAQs

Does the TRD spoiler come pre-painted?

Yes, the FRS TRD rear spoiler comes pre-finished in gloss black from the factory. No additional painting is required after installation.

What kind of hardware is included?

The spoiler kit includes all necessary mounting hardware like bolts, washers, screws, and installation instructions. No additional purchases are required.

Will I need to drill holes in my trunk?

No drilling is necessary. The spoiler uses pre-drilled mounting points that align with existing holes from the factory spoiler.

Is professional installation required?

While professional installation is recommended, mechanically inclined DIYers can install the TRD spoiler themselves with basic tools and patience.

Does TRD manufacture other upgrades?

Yes, TRD produces a full range of performance parts for Scion/Toyota vehicles including lowering springs, sway bars, air intake systems, performance exhausts, and more.